Polytrol is a deep penetrating oil which restores the original colour and appearance of dull or tarnished plastics, gelcoats, metals, and other surfaces.
It penetrates the surface, re-wetting the pigments to restore their lustre and colour which has been lost through exposure to sunlight, rain, and pollution and it also gives corrosion protection. Â When used on tarnished metals, it brings back the shine and gives long-term protection against corrosion.
Simple to apply using a cloth or soft brush, it’s ready to wipe off in just 10 minutes! It can be used on both horizontal and vertical surfaces and can even be used on fibreglass (GRP). Polytrol dries to a tough and long-lasting flexible finish which does not leave a film – so it won’t peel or flake.
Polytrol is now available in a handy 250ml spray can, great for quick application and difficult to reach areas. Please see the directions for use to find out how to apply it.
Ideal Uses for Polytrol Colour Restorer
- Brightening faded car bumpers
- Reviving the gelcoat on your boat
- Restoring the shine to metal fixtures
- Rejuvenating flat or chalky paint dulled by weathering
- Brightening the surface of tiles in stone, terracotta, marble, slate, etc.
- Reviving the colour of faded garage doors
Restrictions
DO NOT use Polytrol on white surfaces, it will not work as Polytrol is designed to restore pigments.
Surface Preparation
All surfaces must be clean, dry and free of dirt, grease, grime and mildew. All waxes, polishes, silicone etc. should be completely and thoroughly removed. Treat any mildew with a 50:50 bleach and water solution. Scrub the solution on to the surface and allow it to stand for 10-15 minutes then rinse thoroughly.
Using Polytrol on plastic, gelcoat, tiles, painted surfaces etc.
Clean the surface with warm soapy water or Net-Trol, rinse thoroughly and allow it to dry for a minimum of 24 hours depending on surface.
Using Polytrol on stone, brick, etc.
Clean the surface with Net-Trol, rinse thoroughly and allow it to dry for a minimum of 24 hours depending on the surface.
Using Polytrol on metal
Clean the surface with warm soapy water and rinse thoroughly or use an appropriate solvent (follow manufacturer’s instructions). Leave the surface to dry for a minimum of 24 hours.
Application of Polytrol Colour Restorer
General directions
Always work in areas that can be completed 10-20 minutes to ensure an even appearance. If the surface absorbs the Polytrol unevenly (i.e. some matt and some shiny patches) move any surplus oil from shiny areas to matt areas. Wipe off any excess Polytrol with a lint free cloth before it becomes tacky. For a shinier finish, buff the surface with a lint-free polishing cloth.
When using the Polytrol 250ml spray can, simply spray on liberally, wipe off any excess and leave to dry.
Applying Polytrol to plastic, gelcoat, tiles, painted surfaces etc.
Apply Polytrol liberally and evenly with a brush or cloth. Allow it to work for 10-20 minutes. Wipe off any excess with a clean lint-free cloth. Leave it to dry.
Applying Polytrol to stone, brick, etc.
Apply Polytrol liberally and evenly with a brush or cloth and leave it to work for 10-20 minutes. Brush out or wipe off any excess Polytrol with a clean lint-free cloth. Leave it to dry.
Applying Polytrol to metal
Apply Polytrol using a fine wire wool (000 grade) soaked in Polytrol and allow it to work  for 10-20 minutes. Wipe off any excess Polytrol with a clean lint-free cloth. Leave to dry.
Note: Polytrol is not a surface coating. Its place is in the surface, not on top.
Maintenance
Maintenance is due when a Polytrol treated surfaces shows signs of fading. Prepare and re-treat surfaces as directed above.
Clean Up
Clean any tools used with white spirit. Polytrol is non-flammable, however any rags, steel wool etc. soaked in Polytrol may spontaneously catch fire if improperly discarded. Rags, steel wool etc must be saturated with water after use or placed in a sealed, water filled metal container, before disposing of them with household waste. Rags may be laid flat and air dried before discarding.
Things to Remember
- Cover and protect everything you do not wish to treat.
- Apply between +5°C and +35°C.
- Do not apply in direct sunlight or on to hot surfaces.
- Do not allow excess Polytrol to dry and create a film on the surface (always remove excess product).
- Do not use Polytrol on white surfaces.
Paul Eyre –
Verified Owner
Used Polytrol on my faded composite door. Very impressed. Easy to apply and quick drying. I was contemplating buying a new door, the fading was that bad, but took a punt on Polytrol and it came up trumps.
george stewart –
Verified Owner
Really surprised , I actually achieved better results then expected I would highly recommend this product
Brian Gilson –
Verified Owner
Being a different material the trim round the glazed panels on my green composite front door were very faded and it looked awful.
I bought a £5 sample tin to try and it made such a difference.
There was enough left to go over the complete door and the result is fantastic.
Highly recommended.
Ian Roberts –
Very quick delivery, product excellent, but has started to fade after 3 weeks , will give the door another coating .
Owatrol Team –
Hi Ian,
Thank you for your comment regarding your experience with Polytrol.
We are sad to hear that you are experiencing fading after such a short period of time.
We would suggest that when you re-apply that you leave it on the surface for a little while longer – the recommendation is to allow it to work for between 10 and 20 minutes.
Perhaps leaving it on the surface for closer to 20 minutes will give you the desired finish that you are looking for.
I hope this was helpful – please don’t hesitate to contact us should you require assistance.
All the best,
The Owatrol Team
Fran –
Verified Owner
My front door had been badly faded by the sun and really didn’t think there was anything on the market that could bring it back to life. I read the reviews and was dubious it would work so bought the small 500ml tin and really didn’t need that much as it is a liquid and a small amount goes a long way. Once applied I can honestly say the door now looks like new. I can thoroughly recommend this product but do wish it could have been purchased locally rather than having to buy online and get delivered.
Ian Bentley –
Verified Owner
Really good product brought my alloy garden furniture up like new. Have provided Wyevale garden centre in Huntingdon with the details as they were not aware of the product and were unable to provide details of any other product to refurbish the furniture.
Peter Bell –
Verified Owner
Satisfied and impressed with the whole process .
Delivery on time.
Easy application.
Finish is excellent, well above expectation.
I estimate that we saved over £1500 by not buying new garage doors.
Thanks.
Matthew Bridle –
Verified Owner
Unbelievable….. I thought i would have to but a new front door, as my dark green upvc door had become milky and very unattractive. I gave it two coats of owatrol and people ha e been asking me if I’ve had a new door. With two coats I got a deep glass shine and the original colour back. I then couldn’t help myself and ended up doing the garage door to match as well. A truly brilliant product …. I never review anything, but am astounded at how good this is and how easy and clean it is to apply.
Peter –
Great product. Perfect results on my brown upvc doors like new
Sue Crawford –
Verified Owner
I have just used Polytrol on my UPVC front door and the results are amazing. The colour has completely been restored and has a great sheen. So easy to apply, I did not have any trouble using the product. Would recommend it to anyone.