Polytrol is a deep penetrating oil which restores the original colour and appearance of dull or tarnished plastics, gelcoats, metals, and other surfaces.
It penetrates the surface, re-wetting the pigments to restore their lustre and colour which has been lost through exposure to sunlight, rain, and pollution and it also gives corrosion protection. When used on tarnished metals, it brings back the shine and gives long-term protection against corrosion.
Simple to apply using a cloth or soft brush, it’s ready to wipe off in just 10 minutes! It can be used on both horizontal and vertical surfaces and can even be used on fibreglass (GRP). Polytrol dries to a tough and long-lasting flexible finish which does not leave a film – so it won’t peel or flake.
Polytrol is now available in a handy 250ml spray can, great for quick application and difficult to reach areas. Please see the directions for use to find out how to apply it.
Ideal Uses for Polytrol Colour Restorer
- Brightening faded car bumpers
- Reviving the gelcoat on your boat
- Restoring the shine to metal fixtures
- Rejuvenating flat or chalky paint dulled by weathering
- Brightening the surface of tiles in stone, terracotta, marble, slate, etc.
- Reviving the colour of faded garage doors
Restrictions
DO NOT use Polytrol on white surfaces, it will not work as Polytrol is designed to restore pigments.
Surface Preparation
All surfaces must be clean, dry and free of dirt, grease, grime and mildew. All waxes, polishes, silicone etc. should be completely and thoroughly removed. Treat any mildew with a 50:50 bleach and water solution. Scrub the solution on to the surface and allow it to stand for 10-15 minutes then rinse thoroughly.
Using Polytrol on plastic, gelcoat, tiles, painted surfaces etc.
Clean the surface with warm soapy water or Net-Trol, rinse thoroughly and allow it to dry for a minimum of 24 hours depending on surface.
Using Polytrol on stone, brick, etc.
Clean the surface with Net-Trol, rinse thoroughly and allow it to dry for a minimum of 24 hours depending on the surface.
Using Polytrol on metal
Clean the surface with warm soapy water and rinse thoroughly or use an appropriate solvent (follow manufacturer’s instructions). Leave the surface to dry for a minimum of 24 hours.
Application of Polytrol Colour Restorer
General directions
Always work in areas that can be completed 10-20 minutes to ensure an even appearance. If the surface absorbs the Polytrol unevenly (i.e. some matt and some shiny patches) move any surplus oil from shiny areas to matt areas. Wipe off any excess Polytrol with a lint free cloth before it becomes tacky. For a shinier finish, buff the surface with a lint-free polishing cloth.
When using the Polytrol 250ml spray can, simply spray on liberally, wipe off any excess and leave to dry.
Applying Polytrol to plastic, gelcoat, tiles, painted surfaces etc.
Apply Polytrol liberally and evenly with a brush or cloth. Allow it to work for 10-20 minutes. Wipe off any excess with a clean lint-free cloth. Leave it to dry.
Applying Polytrol to stone, brick, etc.
Apply Polytrol liberally and evenly with a brush or cloth and leave it to work for 10-20 minutes. Brush out or wipe off any excess Polytrol with a clean lint-free cloth. Leave it to dry.
Applying Polytrol to metal
Apply Polytrol using a fine wire wool (000 grade) soaked in Polytrol and allow it to work for 10-20 minutes. Wipe off any excess Polytrol with a clean lint-free cloth. Leave to dry.
Note: Polytrol is not a surface coating. Its place is in the surface, not on top.
Maintenance
Maintenance is due when a Polytrol treated surfaces shows signs of fading. Prepare and re-treat surfaces as directed above.
Clean Up
Clean any tools used with white spirit. Polytrol is non-flammable, however any rags, steel wool etc. soaked in Polytrol may spontaneously catch fire if improperly discarded. Rags, steel wool etc must be saturated with water after use or placed in a sealed, water filled metal container, before disposing of them with household waste. Rags may be laid flat and air dried before discarding.
Things to Remember
- Cover and protect everything you do not wish to treat.
- Apply between +5°C and +35°C.
- Do not apply in direct sunlight or on to hot surfaces.
- Do not allow excess Polytrol to dry and create a film on the surface (always remove excess product).
- Do not use Polytrol on white surfaces.
I.Healy –
Verified Owner
I’m very pleased with Polytrol spray, I used it to restore the colour on my sun faded composite door. So far I’ve used only one coat and the door looks really good, it was very easy to apply. Great product.
David Burke –
Verified Owner
My brown GRP front door has been blasted by the sun for the last 11 years. It was fading and looking dreadful.
I used Polytrol as per the directions and, literally, it looks like new. It was actually easier to apply than the instructions suggested.
I have since applied it to all my brown plastic windows and it they too are looking like new.
I am not sure how long the improvement will last but so far the results have been brilliant.
Highly recommend
Maureen –
Verified Owner
I tried loads of stuff that didn’t work – this does. Very pleased with the result. My door looked very bad and has been restored with 2 coats.
A Green –
Verified Owner
I highly recommend this product, the frames and sills on my holiday home were looking very tired and neglected. With one coat of Polytrol they look like new am very pleased with result. Delivery was quick and well packed can’t fault Company or product.
Les Terry –
Verified Owner
I’d given up thinking that I could restore two fibre-glass wood effect garage doors, one of which was particularly faded, but thought that this product was worth a “last ditch” try. The result of the first coat was impressive, but after two coats on one and three on the other, they really are “as new”. Time will tell if they weather quickly, but I’m quite happy to give them a quick coat once a year if they look this good.
JOHN –
Verified Owner
Excellent product. You need to see it to believe how good this produce is. Amazing result on a very weathered, 20 year old garage door which now looks like new.
Dean Watkinson –
Verified Owner
Fantastic product expensive but faded garage doors that had been subject to the sun for 10 years. Brought back to looking like when they were first installed.
Jo –
Verified Owner
Great product. Used on my GRP Composite Rosewood front door that had been badly sun damaged. Easy to apply and results are excellent. This product has saved me a lot of money as I thought I would have to replace my door as it looked very bad with almost white patches on it. Door now looks like new. Very pleased I found Polytrol.
Bill –
Verified Owner
I used this to bring a tired looking GRP garage door back to life. The result after one coat was very good. So much so my neighbour thought we actually had our door replaced with a new door. Just make sure you prepare the door well by using an All Purpose Cleaner first.
BAS –
Verified Owner
We had a faded, wood effect, glass fibre garage door. It is one of a pair, but only one is subjected to strong sunlight. We were apprehensive about buying the Polytrol, especially since the delivery charge is relatively high, however, after using the product, the garage door is no longer faded and matches the other door, which was not subjected to direct strong sunlight. Surprised and pleased with the result. The Polytol was delivered the next day, after the online order, the tin was well wrapped in bubble-wrap inside a cardboard box.